Remove unused patches

avrdude-5.11.1-fix-texi-errors.patch

@@ -1,120 +0,0 @@
-diff -Naur avrdude-5.11.1.orig/doc/avrdude.texi avrdude-5.11.1/doc/avrdude.texi
---- avrdude-5.11.1.orig/doc/avrdude.texi	2013-06-17 21:01:46.000000000 +0200
-+++ avrdude-5.11.1/doc/avrdude.texi	2013-06-17 20:58:07.000000000 +0200
-@@ -643,7 +643,7 @@
- the exitspec arguments provided, as follows:
- 
- @table @code
--@itemx reset
-+@item reset
- The `/RESET' signal will be left activated at program exit, that is it
- will be held low, in order to keep the MCU in reset state afterwards.
- Note in particular that the programming algorithm for the AT90S1200
-@@ -652,24 +652,24 @@
- a previous invocation of AVRDUDE with this option specified is one of
- the possible ways to guarantee this condition.
- 
--@itemx noreset
-+@item noreset
- The `/RESET' line will be deactivated at program exit, thus allowing the
- MCU target program to run while the programming hardware remains
- connected.
- 
--@itemx vcc
-+@item vcc
- This option will leave those parallel port pins active (i. e. high) that
- can be used to supply `Vcc' power to the MCU.
- 
--@itemx novcc
-+@item novcc
- This option will pull the `Vcc' pins of the parallel port down at
- program exit.
- 
--@itemx d_high
-+@item d_high
- This option will leave the 8 data pins on the parallel port active
- (i. e. high).
- 
--@itemx d_low
-+@item d_low
- This option will leave the 8 data pins on the parallel port inactive
- (i. e. low).
- 
-@@ -839,13 +839,13 @@
- The @var{op} field specifies what operation to perform:
- 
- @table @code
--@itemx r
-+@item r
- read the specified device memory and write to the specified file
- 
--@itemx w
-+@item w
- read the specified file and write it to the specified device memory
- 
--@itemx v
-+@item v
- read the specified device memory and the specified file and perform a verify operation
- 
- @end table
-@@ -855,16 +855,16 @@
- the file to read or write.  Possible values are:
- 
- @table @code
--@itemx i
-+@item i
- Intel Hex
- 
--@itemx s
-+@item s
- Motorola S-record
- 
--@itemx r
-+@item r
- raw binary; little-endian byte order, in the case of the flash ROM data
- 
--@itemx m
-+@item m
- immediate mode; actual byte values specified on the command line,
- separated by commas or spaces in place of the @var{filename} field of
- the @option{-U} option.  This is useful
-@@ -874,25 +874,25 @@
- leading zero (@code{0}) it is treated as octal.  Otherwise, the value is
- treated as decimal.
- 
--@itemx a
-+@item a
- auto detect; valid for input only, and only if the input is not provided
- at stdin.
- 
--@itemx d
-+@item d
- decimal; this and the following formats are only valid on output.
- They generate one line of output for the respective memory section,
- forming a comma-separated list of the values.
- This can be particularly useful for subsequent processing, like for
- fuse bit settings.
- 
--@itemx h
-+@item h
- hexadecimal; each value will get the string @emph{0x} prepended.
- 
--@itemx o
-+@item o
- octal; each value will get a @emph{0}
- prepended unless it is less than 8 in which case it gets no prefix.
- 
--@itemx b
-+@item b
- binary; each value will get the string @emph{0b} prepended.
- 
- @end table
-@@ -1724,7 +1724,7 @@
- and socket card:
- 
- @multitable @columnfractions .25 .25 .5
--Routing card @tab Socket card @tab Devices
-+@item Routing card @tab Socket card @tab Devices
- @item @code{} @tab @code{STK600-ATTINY10} @tab ATtiny4 ATtiny5 ATtiny9 ATtiny10
- @item @code{STK600-RC008T-2} @tab @code{STK600-DIP} @tab ATtiny11 ATtiny12 ATtiny13 ATtiny13A ATtiny25 ATtiny45 ATtiny85
- @item @code{STK600-RC008T-7} @tab @code{STK600-DIP} @tab ATtiny15